5 Laws That Can Help The Fiat Panda Key Fob Replacement Industry

Reasons Your Fiat 500 Key Fob Won't Work

A key fob for the Fiat 500 is a great way to unlock the doors and get started the car. However, there are many reasons why the fob won't be working. This includes a dead battery or water damage, issues with the receiver module, and interference.

This listing is for a NEW replacement key fiat 500 Fiat Flip Key Remote that appears similar to the Ilco brand. It must be professionally programmed (click here to search for local locksmiths in the automotive industry). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob that isn't working. Modern key fobs only have limited operating range and must be within a few inches of your vehicle to function. If you are far from your vehicle and you press the key fob button, the car will not respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery of your coin cell (Part number CR2032) by a new one from a reputable manufacturer such as Panasonic, Duracell, or Energizer. You can typically find them at your local hardware store, or [Redirect-302] online.

After you've changed the battery on the coin cell It is possible to test it by standing in front of your Fiat 500 and pressing the buttons. The car should flash its parking lights and the key fob should operate the lock and unlock buttons.

If your key fob still doesn't work even after replacing the battery, there may be water damage that prevents it from interacting with the module inside your vehicle. Water damage can happen in a variety of ways, ranging from a light splash to submerging the fob in salt water at the beach. If you suspect your fob was exposed to water, try putting it in a dry rice bag to draw the moisture back out. If this isn't working, you'll need to have your fob replaced by an auto locksmith or dealer.

Water Damage

Water damage can occur if you submerge the fob in the ocean or wash it in a washing machine. Saltwater can cause the circuit board to short and eventually die. In the event that you let your fob get wet, it's not a good idea but if you drop it in the water in a cup or fail to remove it from your pants pocket before running the washer, don't give up hope.

First remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl or a similar product. Test the fob next to determine if it's working. If the key isn't working, it may have to be changed. This is usually handled by an auto locksmith or dealer.

If the key is older and has never been programmed to your vehicle It will most likely need to be replaced completely. A professional locksmith for automotive can carry out this simple task. The locksmith needs to cut the key to match the ignition on your vehicle. They'll also have to reprogram the fob in the car's system. This is a cheap and quick procedure that can be completed within the same day.

Receiver Module Issues

Your 500 key fob may be inoperable because it's out of range. The remote typically has an operating range of 30 feet or less and if it's far from your vehicle, it will not respond to your commands. This can be easily fixed by moving it closer to your vehicle until it starts responding.

If your fob won't work after replacing the battery in the coin, also called a "button", "watch" or "button" It could be a problem with the internal circuit board. In the majority of cases, reprogramming your fob will resolve this issue. You can find the steps for most vehicles on YouTube or in the owner's guide.

It may be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they become loose, it can stop your coin battery from being properly seated, causing your remote to malfunction.

In rare cases it is possible that the fob will become desync'd with your vehicle due to software problems or hardware issues. This can cause a major trouble, but you could often fix this by visiting an auto locksmith to reprogram your fob for you. In certain instances they may have to reinstall the software on your body control module as well.

Interference

Interference can also cause the key fob to not be able to receive or transmit an signal. This can occur when the keyfob is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons why the key fob could not function may be a lack of connection to the buttons or damage to the internal chip, or water damage.

If the key fob been unable to function for a while out of the blue or after trying everything you can at home to fix it e.g. You may have a faulty 500 receiver module If you've tried replacing it with a battery, reprogramming, or using an alternative key fob. The receiver module, located beneath the dashboard, [Redirect-Java] detects radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's internal system, including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Then, reconnect the battery. This will get rid of any remaining electrical charge and restart the car's computer system, which could allow you to the key fob to function again. If the issue persists you should seek out an experienced technician. They will be able to determine the root of your problems.