The Expert Guide To Fiat Panda Key Fob Replacement

Reasons Your fiat panda key fob replacement 500 Key Fob Won't Work

A key fob for the fiat 500 key fob reset 500 is a great way to open the doors and start the car. However, there are a variety of reasons why the fob may stop functioning. It could be due to a dead battery or damage to the receiver module, water problems, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It has to be professionally programmed (click here to find local locksmiths in the automotive industry). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob will not function is the battery is dead. Key fobs of today have a limited range of operation and must be within a few inches of the vehicle to function. If you are further away from your vehicle and press the keyfob button, it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the coin cell battery (Part number CR2032) with a brand new one from a trusted brand such as Panasonic, Duracell, or Energizer. You can find them in your local hardware store, or on the internet.

You can test the coin-cell battery by pressing the buttons while you are standing close to your fiat Punto Key fob replacement 500. The car should blink its parking lights and the key fob should operate the lock and unlock switches.

If your key fob still isn't working after replacing the battery, there may be water damage that hinders it from communicating with the module in your vehicle. Water damage can happen through a variety of methods, including an easy splash or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this fails, you'll need to have the fob changed by an auto locksmith or dealer.

Water Damage

While the fob has some rubber seals that keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can be particularly harmful to the circuit board of the fob and can cause it to short out and eventually end up dying. Getting the fob wet is not an ideal idea but if you drop it in the water in a cup or fail to remove it from your pants pocket prior to running the washer Don't give up hope.

First, remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or a similar product and dry it completely before replacing the battery. Next try the fob and see if it works. If the fob doesn't work it could need to be changed. This is usually done by a dealer or professional auto locksmith.

If the key is a newer model and hasn't been programmed to your car It is likely that it needs to be replaced completely. A professional automotive locksmith can do this job. The locksmith will need to cut the key to match the ignition in your vehicle. They will also need to reprogram fiat 500 key fob the fob to your car's system. This is a low-cost and fast process that can be completed on the same day.

Receiver Module Issues

The 500 key fob could not function because it's out of range. The remote has a range of 30 feet, so when you're too far away from your vehicle, it won't respond to your commands. It is possible to fix this by moving the remote closer to your vehicle until it responds.

If you've replaced your coin battery (commonly known as a "button" or "watch") and your fob doesn't function, it could have an internal circuit board problem. Reprogramming your fob can resolve the issue. You can find directions on how to do this for most vehicles by searching YouTube or checking out the owner's manual.

You may need to replace the metal clips that keep the battery of your coin in place. If they lose tension, it can prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare cases the fob could be out of the vehicle's sync because of hardware or software issues. This could be a huge problem, but you can frequently fix this issue by visiting an auto locksmith to have them reprogram your fob for you. In some cases, the software may also require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit the signal. This could occur if the keyfob is in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons the key fob may not function may be a lack of connection to the buttons or damage to the internal chip or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to solve the issue (e.g. You may have a faulty 500 receiver module if you've tried replacing the battery, reprogramming it, or using an alternative key fob. The receiver module, located under the dashboard, picks up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Luckily, there is an easy method to reset all of the on-board systems in your 500 device, including the key fob. Disconnect the battery 12 volt for approximately 15 minutes by removing the negative cable first then the positive cable. Then reconnect the battery. This will eliminate any remaining electrical charge, and then restart the computer in your car. This can help you get your key fob to work again. If the issue continues you should speak with an experienced technician. They will be able to identify the exact cause of issues.