9 Lessons Your Parents Taught You About Patio Door Lock Repair

Patio Door Lock Repairs

Over time, the wear and tear can cause lock malfunctions. However, there are easy and efficient methods that can restore your uPVC patio door's security.

If it's resetting the lock or cleaning the mechanism that locks these simple fixes will help you make your home more secure.

Clean the Lock

patio door repair doors are ideal for bringing the outdoors in and keeping the elements out. However, they can be an issue for security in the event that the lock isn't working properly. With time wear and tear cold and hot weather dirt and debris can take their toll on your patio door's lock and cause it to become difficult to open. With a little care, you can ensure your patio door's locks always perform correctly.

It's essential to clean the lock on your patio door and all the moving parts. This will help remove any grime or coatings that could be preventing your lock from functioning effectively. Start by wiping down the moving parts of your patio door's lock using a damp cloth. then make use of a scouring pad, or a rough damp cloth to scrub any hard-to-reach parts of the door and frame that are ingrained with dirt. You should then wipe down the entire lock using dry cloth to get rid of any remaining dampness and allow it to air dry before applying it to the next time.

If your patio door uses pin-tumbler latches you can apply powdered Graphite on the key. You can also use a Teflon oil like WD-40 Multi Use Product. This type of lubricant is easy to apply, and it won't disintegrate with time. If you're unable find the right lubricant to use with your lock, apply a pencil that has a thicker tip. Put the pencil in the lock, then shake it around to distribute the graphite.

Regular maintenance is also essential to keep the tracks of sliding patio doors free from dirt, dust and debris. These tracks are especially susceptible to ice, snow, and other debris, which could cause them to jam or bind. This can make it difficult for your patio door lock repair, get more info, door to open and close.

Sliding patio door track rails and rollers can be cleaned by removing dirty or damaged weather stripping, cleaning them, then installing it. The rollers for patio doors can be cleaned and sprayed down with an oil that is non-stick.

Lubricate the moving parts

uPVC French Doors, similar to sliding patios, are operated with 3 to 4 or occasionally 5 point locking mechanisms. This includes the lock cylinder and handle that is operated by keys. These doors require maintenance, oiling of the moving parts. This can be done using an oil that is thin, but never WD40. This should be done at least once per year.

If sagging hinges aren't a reason, the door could be misaligned and catching or rubbing against the strike plate hole within the frame. Remove the strike plate and employ a sharp tool expand the mortise. This will allow the latch to fit into the hole and prevent it from rubbing against the frame.

While the cylinder is out of the way take a measurement of its width using an object or a piece of wood that will fit in the gap between the adjustment screw and the lock. The outer dimension is the distance from the outside of the door to the middle of the cylinder. the inner dimension runs from the center of the adjustment screw until the end of the cylinder.

Check the lock's width

If your patio door latch is difficult to turn even after cleaning and oiling it's possible that it's not aligned with the strike plate. Examine if the door is balanced and if the hinge screws are secure however, in many instances it is possible to move the strike plate up or down can correct the issue.

The latch may not be able to engage properly if the strike of the lock is too small. In this case, enlarge the opening using the hammer and chisel. Then, test the latch so that it doesn't rub against the door jamb frame or catch the frame.

You must identify the kind of mortise lock that you have before buying a replacement. This can be done by looking at the faceplate and noting whether it is square or round. Take a look at each screw hole in the existing lock, and note their size. This will enable you to find the replacement lock that has the exact same width and will fit into your existing hole.

You'll need to locate the mortise lock and inspect it for scratches, bends, or other damage that requires to be fixed. A bent or damaged latch is more likely to break than one that's been used much, so be sure to replace the lock with a new, secure version if you find any signs of wear or damage.

After you've determined the type of lock replacement you need, it's now time to start the actual repair. Take the old handle and spindle from your patio sliding doors repair door, and then install the new one. Start by putting in the handle in the interior by aligning it with the spindle and then securing it with the two bolts or screws that secure it. Once the handle in the interior is installed, you can install the exterior handle and screw it in the position as well. After you've completed the steps you can test the new handles to ensure that they can be opened and closed easily and that the latch is catching correctly with the strike plate.

Check the Door's Strike

The strike plate and door latch are two pieces that work together in order to lock the door. If these parts aren't aligned correctly and the latch doesn't latch the door shut correctly. This problem is usually very simple to solve.

First, examine the strike plate's receiving holes to ensure that they are free of obstructions, such as dirt or plastic plugs. Loosen the keeper screws holding the strike plate. This will allow it to move vertically but it will not be able to separate from the frame. Then, you can adjust the strike plate until its holes for receiving align with the latch hooks on the door latch. Once the strike plate has been adjusted, tighten all screws and test if the door closes smoothly.

These plates are difficult to reach for homeowners with sliding patio doors. However, they are essential to lock and unlock your door. The plates made of metal are located at the top and bottom jambs of the door which are where they help support the latch. The door latch slides into this strike plate and creates the seal. If the strike plate is damaged, rusted, or not installed correctly, it can stop the latch from locking the door securely.

A misalignment between the strike plate and latch is one common cause for the patio lock not to close or stick. The easiest method to check for this is with the "lipstick test." Apply some lipstick on the edge of the deadbolt and put masking tape on it. The lipstick will leave the mark when you shut the door. This will show you exactly where the latch meets the strike plate. If the mark is too low or high it is possible to alter the strike plate.

If your sliding patio door locks aren't functioning properly they can help keep your home safe from burglars. You need to fix this problem as soon as you can. Follow these easy steps to fix your patio door lock and restore it's function.